HPE ProLiant DL20 Gen11
Configuration Proposal
| 1x | P65395-421 | HPE ProLiant DL20 Gen11, Intel Xeon E-2434 4 Core 3.4 GHz, 16 GB RAM, 4x LAN, backplane for HDDs with SFF (2.5") Basic Carrier, rackmount kit |
| 2x | P40503-B21 | 960 GB SATA-SSD 2.5" Hot-Plug, SFF Basic Carrier |
| 1x | P65407-B21 | Dedicated iLO network port + M.2 slot |
Certified Models
| P65393-421 | 2x LFF (3.5") Non-Hot Plug Backplane for hard disks without carrier |
| P65394-421 | 2x LFF (3.5") Hot Plug Backplane |
| P65395-421 | 4x SFF (2.5") Hot Plug Backplane |
| P65396-421 | 4x SFF (2.5") Hot Plug Backplane |
| P71375-425 | 4x SFF (2.5") Hot Plug Backplane |
Slots and network cards
- 4 network ports with 1 GBit/s are already integrated in the basic device
- In contrast to previous generations, the device has a slot for PCIe cards with full height and half length (1x FHHL), as well as a slot for network cards in OCP3 format
- A separate cable set is required so that the OCP3 slot can be used
 |
P65411-B21 | Cable set for OCP3 slot |
Certified PCIe network cards
|
P21106-B21 | HPE I350-T4 4-port Gigabit network card, PCIe |
|
P08443-B21 | Intel E810-XXVDA2 2-port SFP28 network card, 10/25 GBit/s, PCIe |
|
P08458-B21 | Intel E810-XXVDA4 4-port SFP28 network card, 10/25 GBit/s, PCIe |
Certified network cards OCP3
|
P08449-B21 | Intel I350-T4 4-port Gigabit network card, OCP3 |
|
P10106-B21 | Intel E810-XXVDA2 2-port SFP28 network card, 10/25 GBit/s, OCP3 |
Certified hard disks and SSDs
|
801882-B21 | 1 TB SATA hard disk 3.5" non-hot-plug, without HDD carrier |
|
801888-B21 | 4 TB SATA hard disk 3.5" non-hot-plug, without HDD carrier |
|
861686-B21 | 1 TB SATA hard disk 3.5" hot-plug, LFF LP carrier |
|
861681-B21 | 2 TB SATA hard disk 3.5" hot-plug, LFF LP carrier | |
861683-B21 | 4 TB SATA hard disk 3.5" hot-plug, LFF LP carrier | |
P40503-B21 | 960 GB SATA-SSD 2.5" Hot-Plug, SFF Basic Carrier | |
P40504-B21 | 1.92 TB SATA-SSD 2.5" Hot-Plug, SFF Basic Carrier | |
P40505-B21 | 3.84 TB SATA-SSD 2.5" Hot-Plug, SFF Basic Carrier |
Notice: Make sure that the hard disk and carrier match the backplane of the server (see above).
Notice: The device does not have a loudspeaker. When using RAID, it is therefore not possible to receive an acoustic warning if a hard disk fails. The use of a monitoring system is therefore recommended.
Memory Expansion
|
P64336-B21 | 16 GB DDR5-4800 ECC UDIMM memory extension |
|
P64339-B21 | 32 GB DDR5-4800 ECC UDIMM memory extension |
Different DIMM memory sizes cannot be mixed within one memory channel
iLO Management
- The system always includes the iLO Baseboard Management Controller (BMC)
- It can be accessed via one of the integrated network ports or a dedicated network port
- If iLO is to be used, Intra2net recommends using only the dedicated iLO network port to increase reliability
|
P65407-B21 | Dedicated iLO network port + M.2 slot |
Rack
| Height of the Server 1U, Depth only 382 mm |
| A rackmount kit is supplied by HPE |
| Fits racks from HPE and many other manufacturers |
| Alternatively, the following installation kit can be used: Racksolutions 122-2413 |
BIOS Settings
For correct operation, the following settings must be configured in the BIOS setup:
|
System Configuration > BIOS/Platform Configuration > System Options > Server Availability Automatic Power-On : Always Power On |
|
System Configuration > BIOS/Platform Configuration > Storage Options > SATA Controller Options Embedded SATA Configuration : SATA AHCI Support |
|
System Configuration > BIOS/Platform Configuration > Server Security Secure Boot Settings > Attempt Secure Boot : Disabled |
Back to HPE Server Overview